Can i glaze over polyurethane

Christmas Trees. Holiday Lighting. Gift Cards. Glaze over Polyurethane to darken finish. Email Save Comment 8. Featured Answer. Like 1 Save. Sort by: Oldest. Newest Oldest. Related Discussions Refinishing fir to match existing finished trim from Q. Old wood always looks like it has "darkened" with time. Technically, it hasn't. It is the oil-based finishes they used to treat the wood that has darkened. When you "strip" the finish you will find that the wood underneath is lighter than the finish.

The wood colour underneath is the real colour of the wood. Today's water based finishes will not darken. Only products that are "oil based" or "oil modified" will darken wood. This will be the same as your fir. Once you find the original colour underneath, you will need to decide if you will introduce an oil product usually solvent based, bad smell, etc or try for an "oil modified" water based product like Minwax.

If you like the original colour, then use a water based polyurethane. As to "matching" the upstairs, I'm not sure why you would need to do this. The spaces are separate physically and visually and the "theme" of reddish wood will "mentally" work well as you move from one space to the other. I actually find the transition of the darker red wood trim upstairs does well as you move down the stairs and enter into the "light bamboo" finished floors in the basement!

The complimentary tones live very nicely together!! Is that cork in the basement I see? The first thing: what type of paint did you use, was it made for cabinetry, and what brand is compatible with the paint?

The answer to your question will be found in the answers in these 3 questions. As a landscape builder, he helped establish two gardening companies.

By Chris Deziel. Related Articles. For a vintage look, rub the glaze down with another color after it cures or wipe the partially dried glaze to reveal some of the original color to simulate an aging finish.

Avoid using water-based polyurethane. It doesn't adhere as well to a cured polyurethane finish as the oil-based products. If the glaze develops defects like bubbles or drips as it dries, you may have to accept them as part of the finish.

Click to see full answer Similarly, can you glaze over polyurethane? You can change the tone of your cabinets -- without the hassle of stripping and restaining -- by glazing right over their existing polyurethane finish. A glaze is essentially a clear finish with added pigment that renders it translucent. Oil-based polyurethane and epoxy resin glazes work best on cured polyurethane.

Similarly, can you glaze over lacquer? Since you are going over a lacquer finish, I suggest that you do not use a lacquer based glaze. It is very helpful to shoot the first glaze coat a bit on the light side, as it is very easy to shoot another coat possibly diluted with more clear finish , but quite difficult to remove some color if you get it too dark. As nouns the difference between glaze and varnish is that glaze is ceramics the vitreous coating of pottery or porcelain; anything used as a coating or color in glazing see transitive verb while varnish is a type of paint with a solvent that evaporates to leave a hard, transparent, glossy film.

Theoretically, almost any stain could be used as a glaze. However, most glaze formulations are thicker than stain to allow more control and manipulation of the color and tend to have more intense coloration, since very little glaze will be left on the surface. As with stains , some are fast drying and some slow drying. Apply Antiquing Glaze Add a small amount of antiquing glaze to a smooth, clean rag.

Begin applying the glaze to the front or side of one cabinet in small, circular motions until you've covered the entire section. Tip: A small amount of glaze will go a very long way.

Think of stains and glazes as the color, and the topcoat as the protectant. Antiquing consists of a glaze applied over a base finish; the first step is applying an enamel base coat to the wood. Antiquing is the technique of glazing a base finish to simulate age or create an interesting color effect.

If you're working over an existing finish, make sure the glaze is compatible. What does epoxy resin not stick to? Epoxy resin adhesives will bond all woods, aluminum and glass well. It does not bond to Teflon, polyethylene, polypropylene, nylon, or Mylar.

It bonds poorly to polyvinyl chloride, acrylic and polycarbonate plastics. The only way to tell if an epoxy will bond to a material is to try it. How do you shine epoxy after sanding? Steps Use soap and warm water to clean your resin piece, if necessary. Wet sand the resin with grit sandpaper to remove any scratches. Repeat the sanding process with increasingly finer grit sandpaper. Dry off your resin piece with a towel to remove any grit or dust. Can you put epoxy over oil based stain?

Applying epoxy over stained surfaces. Our product is not designed to be used over oil based stains, urethanes, or paints. If an oil based stain has already been applied the official recommendation would be to strip and re-stain with a water based product.

How do you make dough less salty? How do I reset my key fob after replacing the battery? Co-authors 8.